Minwax Fast-drying Polyurethane Gloss Oil-based 32-fl Oz Polyurethane Review

Directions

Instrucciones en Español

For aerosol directions, click here

Interior Use Only

Alarm! Removal of erstwhile paint by sanding, scraping or other means may generate dust or fumes that contain pb. Exposure to pb grit or fumes may cause brain damage or other adverse health furnishings, peculiarly in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such every bit a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Atomic number 82 Information Center at ane-800-424-LEAD (in Us) or contact your local wellness authority.

Directions:

1. Surface must be dry and free of old finishes in poor status, paint, wax, grease, polish, clay or other foreign matter.
2. Sand to obtain a smooth uniform surface. Remove all dust with a material dampened with mineral spirits.
3. If desired, use stain, such as Minwax® Forest Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry out times.
4. Stir Minwax® Fast-Drying Polyurethane before and during apply to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
6. For floor projects, use a foursquare buff orbital or disk-type sander with 220 grit sandpaper or the equivalent grit pad or screen (specifically designed for sanding between coats). Practice not utilize a belt or drum-blazon sander for sanding betwixt coats. Follow the sander manufacturer's directions for your type of project.
7. Use second coat. If third coat is desired, repeat pace 6 before application.
8. After final coat, allow 24 hours before light use.

When used on hardwood floors, apply a lambswool or synthetic pad applicator or natural bristle brush and maintain a moisture edge to avert lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours subsequently final coat. When replacing furniture, do non slide. Do not install rugs or clean floors for seven days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer'south safety instructions.

COVERAGE: Approximately 125 foursquare feet per quart.

Notation: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, college humidity, lack of air move or application of thick coats will extend drying times. Always exam tackiness between coats. Do non sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over calorie-free-colored wood surfaces. Always spot exam on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish or Minwax® Ultimate Floor Finish.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residuum may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding balance in a sealed, h2o-filled, metal container. Dispose of in accord with local burn down regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If yous experience eye watering, headaches, or dizziness, increment fresh air, or wear respiratory protection (NIOSH approved) or go out the expanse. Avoid contact with eyes and peel. Wash easily after using. Keep container airtight when non in use. Do not transfer contents to other containers for storage.

Outset AID: In case of eye contact, affluent thoroughly with large amounts of water for 15 minutes and get medical attending. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, phone call Poison Control Center, hospital emergency room, or dr. immediately.|

DELAYED Effects FROM LONG TERM OVEREXPOSURE. Contains solvents which tin can crusade permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents tin exist harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive impairment.

DO NOT Take INTERNALLY. KEEP OUT OF THE Accomplish OF CHILDREN.

Droplets Directions

Interior Use Only

Alert! If you scrape, sand or remove former paint, you may release lead dust. Lead Is Toxic. Contact the National Atomic number 82 Data Hotline at one-800-424-LEAD or log on to www.epa.gov/atomic number 82.

1. The surface must be dry and free of old finishes in poor condition, pigment, wax, grease, shine, dirt or other foreign thing.
2. Sand to obtain a smoothen, uniform surface. Remove all dust.
3. If desired, apply stain, such as Minwax® Forest Finish™ Stain, to unfinished wood surfaces. Follow directions for awarding instructions and dry times.
4. Shake Minwax® Fast-Drying Polyurethane vigorously for two minutes. Shake for 10 seconds occasionally during use.
5. Protect adjacent areas from overspray. Wet overspray can be removed with mineral sprits.
6. Hold can vertically 12 inches from surface. Depress push fully and spray using an even, sweeping move with slightly overlapping strokes. On unfinished wood, apply sufficient fabric to seal open joints, edges and end-grain.
7. Utilize thin coats to avert runs and sags. Recoat inside 2 hours. If unable to do and so, expect a minimum of 72 hours, then lightly sand and recoat.
8. Utilise at to the lowest degree 3 coats on unfinished wood and two coats on surfaces already finished.
9. After final coat, allow 24 hours before normal use.

Note: To a higher place dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, college humidity, lack of air movement or application of thick coats will extend drying times. Slight ambering may be experienced when Polyurethane is practical over light-colored wood surfaces. E'er spot test on an inconspicuous expanse to ensure satisfactory results. Minwax® Polycrylic® Protective Terminate is recommended over low-cal-colored woods surfaces.

Nozzle Care

1. After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
2. If spray button becomes clogged, article of clothing middle protection, wipe off button opening with lacquer thinner- Do NOT stick pin in spray button opening.

CLEANUP: For easy clean-up, use lacquer thinner following the manufacturer's safety instructions.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residual may spontaneously catch burn down if improperly discarded. Immediately place rags, steel wool, other waste soaked with this production, and sanding residual in a sealed, water-filled, metal container. Dispose of in accordance with local burn regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS AND KETONES. DANGER! EXTREMELY Combustible.

Continue abroad from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. Keep surface area ventilated during utilize and until all vapors are gone. Practice Non SMOKE - Extinguish all flames, pilot lights and heaters -Turn off stoves, electric tools and appliances, and any other sources of ignition. CONTENTS UNDER Force per unit area. Avert prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may crusade bursting. Do not puncture, incinerate, burn or store in a higher place 120°F. Keep upright in a cool, dry place. Do not discard empty tin in trash compactor.

VAPOR HARMFUL. Apply with adequate ventilation. Avoid continuous animate of vapor and spray mist. To avoid breathing vapors or spray mist, open up windows and doors or utilise other means to ensure fresh air entry during awarding and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or go out the area. Overexposure may cause numbness in extremities which tin can persist for some menstruation of time and may be permanent. Avoid contact with eyes and skin. Wash hands after using.

First AID: In case of eye contact, flush thoroughly with large amounts of h2o for fifteen minutes and get medical attending. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and phone call md.

DELAYED Furnishings FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent encephalon and nervous system harm. Intentional misuse by deliberately concentrating and inhaling the contents tin can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Do NOT Take INTERNALLY. Go on OUT OF THE REACH OF CHILDREN.

CONFORMS TO ASTM D-4236. Contact a doctor for more health information.

Frequently Asked Questions

What is the best way to select a sheen?

Sheen choice is a personal preference. Satin sheens reflect less light and gloss sheens reflect more than lite.

Is 1 sheen more durable than the others?

No. The additives that distinguish satin from semi-gloss and gloss do not compromise the durability of the finish.

What can be washed to avoid bubbles in the finish?

There are 4 means. Kickoff, stir, don't milkshake, the tin can. 2nd, use a high-quality, natural bristle brush. Third, work the terminate into the wood, simply don't create excess foam. Fourth, "tip-off" the terminate before stopping, carefully running the brush at a 45-degree bending the length of each board in one unbroken movement. This will burst and smooth out any bubbles that may have been created.

Should Minwax® Fast-Drying Polyurethane be sanded between coats?

Aye. A light sanding (#220 sandpaper) will remove any fine particles of dust that have settled on the finish while information technology was yet moisture. Low-cal sanding as well helps abrade the surface, improving intercoat adhesion.

Why does Minwax® Fast-Drying Polyurethane sometimes have longer to dry than the instructions indicate?

The drying fourth dimension is afflicted by the amount of moisture in the air, the air temperature and the thickness of the coats. When humidity is high, temperature is low, or coats are thick, it takes longer for the motion picture to dry out.

What is the best manner to determine how many coats of Minwax® Fast-Drying Polyurethane to employ?

If you expect closely at the wood in bright, straight light, yous should not be able to discover any dry spots. If you do, an boosted coat is necessary to protect the wood.

Does Minwax® Fast-Drying Polyurethane need to exist waxed?

No. Wax does provide an extra layer of protection, simply it will prevent you lot from applying an boosted coat of Minwax® Fast-Drying Polyurethane in the hereafter without get-go removing the wax. Instead, we recommend using Minwax® Forest Cabinet Cleaner to keep wood make clean and looking beautiful.

rewreadion89.blogspot.com

Source: https://www.minwax.com/wood-products/clear-protective-finishes/interior/minwax-fastdrying-polyurethane

Share this post